Influence of different safety shoes on gait and plantar pressure: a standardized examination of workers in the automotive industry (2024)

2.1 . Subjects

Twenty male workers [age: 33.2±10.5 years, height: 177.9±3.9 cm, weight: 80.1±7.8 kg, median foot size: 27.8 cm (min: 26 cm, max: 28.7 cm) ] from the automotive industry (plant operators, plumbers, and quality control inspectors) volunteered for this study and provided informed written consent. All participants had no history of foot pain, were free of injuries, and did not complain about pain or disorders of the lower extremities and back for at least 6 months prior to the beginning of the study. Employees at these workplaces are mainly exposed to standing and walking. All employees provided informed consent.

2.2 . Safety shoes

Three different types of safety shoes were examined in this study (Fig. ​(Fig.1).1). The first safety shoe (shoe 1, "normal" shoe) was a low priced shoe with a flat rubber sole and without any special ergonomic features. The second safety shoe (shoe 2, "cushioned shoe" ) was characterized by forefoot cushioning as well as a bodyweight-adjustable cushioning element in the heel area. Furthermore, shoe 2 was available in four different widths from small to extra wide. The third safety shoe (shoe 3, rocker-bottom shoe) had a curved sole in the anterior-posterior direction.

2.3 . Measuring instrument (CUELA system supplemented by plantar pressure soles)

Body postures, joint angles, and body movements were measured with the CUELA system ( "Computer-unterstützte Erfassung und Langzeitanalyse des Muskel-Skelett-Systems," a computer-assisted recording system, which allows the long-term analysis of musculoskeletal loads at the workplace)^11-14). This person-centered measuring system consists of motion sensors (3D accelerometers Analog Devices ADXL 103/203, gyroscopes muRata ENC-03R, and goniometers), which are attached to the body by Velcro^®-fasteners over clothing or workwear (Fig. ​(Fig.2).2). A small data logger (using a flash memory card) enables the synchronous recording of all measured data of gait and plantar pressure distribution at a sampling rate of 50 Hz.

Simultaneously to the kinetic assessment of the lower extremities, plantar pressure was measured using the in-shoe pressure measurement system paroTec^® (Paromed, Germany), which consists of reusable insoles with a height of 3 mm in different sizes (European 31-48). The insoles hold 24 piezoresistive pressure sensors on each sole at biomechanically relevant measuring points (Fig. ​(Fig.3)3) and are fit into the respective shoe.

The CUELA software is able to display data (in this case kinetic and plantar pressure data) simultaneously to the measurements with a 3D animated figure and a digitalized video of the measurements¹⁵⁾. These features were used for the analysis of the measurements, where one examiner analyzed the recorded measurements.

2.4 . Experimental design

After an individual fitting, all participants received one pair of each study shoe and were obliged to wear each type of shoe for at least two weeks at their workplaces prior to the respective measurements (habituation phase).

After fitting the CUELA motion sensors and the associated shoe insoles, the insoles were calibrated in compliance with the manufacturer's guidelines, and the CUELA system was initialized. Standing upright (relaxed) was used as the reference posture and all angles in this position were defined as 0°. Insole calibrations and initializations of the CUELA system were made before each measurement.

Motion and plantar pressure measurements were conducted on participants, who were equipped with the CUELA system and instructed to walk at a defined speed of 1.5 m/s (controlled by a metronome) along a 10 m level walkway (according to the protocol of Perry and Burnfield¹⁶⁾). Each participant performed one trial per pair of shoes and hence was measured altogether three times (in-between time intervals: approximately four weeks, because of the prior habituation phase (as described above) ). The level walkway was typical industrial concrete and made of magnesite screed.

The study was conducted in accordance with the Helsinki Declaration of 1975, as revised in 2000¹⁷⁾.

2.5. Outcome parameters

Gait: The following joint angles were assessed by CUELA measurements to describe motion during gait (Fig. ​(Fig.22):

・Trunk inclination angle: the sagittal inclination angle of the thoracic (T3) and lumbar spine (L5)

・Hip flexion angles: the angle between pelvis axis and thigh axis in sagittal plane (left and right hip)

・Knee flexion angles: the angle between thigh axis and lower leg axis in sagittal plane (left and right knee)

Fiftieth percentiles (50^th), and the Range of Motion (RoM; i.e., the difference between the 5^th and the 95^th percentile) were calculated.

Plantar pressure: To localize areas of maximum pressure, the insoles were divided in eight zones (zone 1: heel-zone 8: toes) with two to four measure points. The mean value and standard deviation (SD) of the two most loaded measuring points per zone were calculated and used for further analysis. In addition, the course of the center of pressure (CoP) in posterior-anterior and medial-lateral direction was analyzed to describe the rolling characteristics of the participants' feet in the respective shoes (fiftieth percentiles (50^th), and Range of Motion (RoM; i.e., the difference between the 5^th and the 95^th percentile) (Fig. ​(Fig.22).

2.6 . Data processing and statistics

After aligning the measurements and the video-documentation of the walk, five steps of both feet from the middle of the walking distance were selected and averaged for each subject. These data were processed by the CUELA software to calculate motion variables and plantar pressure values during the gait cycle. Initial descriptive statistical evaluation was also conducted with the CUELA software¹¹⁾. The SPSS^® software (IBM, Version 23.0) was used for further statistical analyses. ANOVA analyses for repeated measures (General Linear Model, GLM) were applied to motion data and plantar pressure values to determine the changes in gait and pressure with regard to different safety shoes and different zones of the insole (zones 1-8). Post-hoc multiple comparisons were performed using the LSD (Least Significance Difference) technique with the level of significance being set at p<0.05.

3.1 Motion analysis - gait

Walking in the three different safety shoes resulted in statistically significant differences in gait measurements (Table ​(Table11).

The 50^th percentile of trunk inclination and hip flexion differed significantly between shoes, particularly between "normal" shoe 1 and the other two shoes. With regard to knee flexion, there were no statistically significant differences in the 50^th percentile between the three different shoes.

The three different shoes showed approximately the same RoM of trunk inclination (~19°) and approximately the same RoM of hip flexion (~30°), but the RoM of knee flexion differed significantly between the three shoes. Particularly shoe 2 seemed to cause a slightly larger RoM when compared to shoes 1 and 3. This might be associated with an increased step length.

3.2 Plantar pressure distribution and CoP

Maximum plantar pressure values differed with regard to shoe and with regard to the zone of measurement. From heel to toe, shoe 1 ( "normal" shoe) caused the highest pressures in zones 1 and 2 (heel area) as well as in zone 7 (forefoot), whereas it showed the lowest pressures in the middle area of the foot (zones 3-5). The pressure in the middle area of the foot was relatively low for all three shoes, which is in accordance with the natural course of walking. With regard to the forefoot (zones 6-8), all shoes showed their respective maximum pressure in zone 7. Nevertheless, the pressure maximum values differed significantly between the shoes (p<0.001). Furthermore, the pressure maximum in zone 6 was found for shoe 2 (cushioned shoe), in zone 7 for shoe 1 ( "normal" shoe), and in zone 8 for shoe 3 (rocker bottom shoe; Table ​Table2),2), implying differences in the rolling motion.

The RoM of the CoP showed different lengths in posterior-anterior direction with regard to the different shoes. The longest course of the CoP was found for shoe 1 (159.5 mm), followed by shoe 2 (149.1 mm) and then shoe 3 (143.7 mm) (p<0.001). The RoM of the CoP also differed significantly in medial-lateral direction between the different shoes (p=0.003), particularly with regard to shoe 3 (Table ​(Table2).2). Overall, post-hoc tests suggest that the pressure distribution over the pre-defined foot zones was more heterogeneous in "normal" shoe 1 compared to shoes 2 and 3 (Table ​(Table22).

Motion analysis - gait

Winter et al.¹⁸⁾ measured RoMs during a completed stride cycle while walking with a natural cadence and reported a RoM of 32.79° for the hip joint and a RoM of 64.86° for the knee joint. This study found a slightly lower RoM of the hip joint and knee joint when wearing "normal" shoe 1, which could be associated with the fact that the participants were supposed to adapt their cadence to a predefined speed of 1.5 m/s. Surprisingly, the RoM of trunk inclination of the male participants in "normal" shoe 1 (19°) was more than twice as high as the RoM of female participants walking at approximately the same speed in normal sports shoes (9°) in a study of Li and Hong¹⁹⁾. This suggests that the movement of the upper body was more pronounced in our cohort of male workers. This difference might be due to the shoes, due to a gender difference or, eventually, due to a selection bias. Unfortunately, our cohort did not include women, while the cohort of Li and Hong did not include men. Therefore, the question of gender differences needs to be addressed in future examinations.

In comparison to "normal" shoe 1, "cushioned" shoe 2 and rocker-bottom shoe 3 led to a relative backward tilt of the upper body (when regarding the mean value of the 50^th percentile of trunk inclination). Li and Hong¹⁹⁾ also reported a backward shift of trunk orientation when wearing negative-heeled shoes, a finding that is reflected in our results, as shoe 3 can be roughly described as having a negative heel. Similarly, other authors²⁰⁾ have found a backward shift of the trunk when participants wore rocker-bottom shoes. Surprisingly though, the cushioned shoe (shoe 2) showed approximately the same backwards shift of trunk inclination. In ergonomic workplace evaluation, trunk inclination is often used to characterize back loading^21,22). While a forward lean of the trunk is believed to lead to postural strain and to be associated with back problems^23,24), the backward shift while wearing shoes 2 or 3 might be beneficial for preventing back problems at the workplace.

The alterations in trunk inclination were accompanied by a decreased median hip flexion for shoes 2 and 3. The findings with regard to shoe 3 are in accordance with findings of Romkes et al.²⁵⁾ and Nigg et al.²⁶⁾, who examined rocker-bottom shoes in general and found a reduction of peak hip flexion and peak hip extension when compared with walking in shoes with a normal sole geometry. In contrast to the present study, subjects in the study of Romkes et al. were free to choose their own walking speed and therefore walked significantly slower due to a smaller stride length as well as a slight reduction in cadence. Again, the cushioned shoe 2 showed a similar influence on the gait pattern to shoe 3. Measurements have shown that lumbar vertebral posture is largely secondary to the postural relationship between the trunk and the hips²⁷⁾; therefore, a reclined trunk combined with decreased median hip flexion might also be able to prevent the occurrence of back complaints, as the angle between hip and trunk might be more stable.

Participants wearing "normal" shoe 1 showed a smaller RoM of the knee joint (62.3°) than the participants in the study of Winter (64.9°)¹⁸⁾, but also compared to the participants in the study of Li and Hong¹⁹⁾, who wore sports shoes (66.0°). Though the cushioned shoe 2 led to a significantly larger RoM of knee flexion (RoM shoe 2=64.0°), it was still slightly lower than the RoM found by Li and Hong. Larger RoMs of the knee joint are believed to be associated with an increased stride length^28,29), and increased stride lengths increase ground reaction forces³⁰⁾. Nigg und Denoth (1980) showed for running subjects that these forces that function along the leg-axis are, in part, dependent on body mass and knee angle at contact³¹⁾, which might be why persons with lower back problems avoid increased stride lengths^32,33). Apart from ground reaction forces, stride length was also found to be associated with larger spinal rotations, a larger thorax-pelvis relative phase, and a lower pelvis-leg relative phase, while the thorax continues to counter-rotate with respect to the leg³³⁾. As cushioned shoes allow for increased stride length in healthy subjects, one could argue that cushioned shoes might also be beneficial for employees with episodes of back pain because they seem to reduce ground reaction forces and spinal rotation at normal stride length. However to the knowledge of the authors, this assumption has not yet been proven right. Furthermore, recent studies contradict the association between RoM of the knee and stride length and claim that stride length is rather associated with shoe weight, hip RoM, and rotational movements of the pelvis³⁵⁾.

Plantar pressure distribution

Different shoes led to differences in the distribution of peak plantar pressures. The highest peak pressures in the rear and forefoot area were measured when wearing shoe 1, which lacks additional cushioning elements; alternatively, these differences are associated with the differences in gait. Nevertheless, comparative studies have demonstrated that cushioning materials in safety shoes are advantageous when trying to reduce plantar pressure^2,9,36). Due to a forefoot and rear foot cushioning element, shoe 2 showed lower pressure values with the exception of zone 6. In this area there was a transition area of the insole where a low shaped pad and a graphite point for electric static discharge were placed. This construction of the insole might have caused the high pressure values at a critical point, where the metatarsophalangeal joint is positioned. As higher pressure in the metatarsal region was found to be associated with foot/ankle disorders³⁷⁾, this finding is dissatisfying and the shoe construction should be altered. Additionally shoe 2 was associated with an increase in the RoM of the knee, which might in turn lead to longer steps. An increase in stride length was found to be associated with an increase in plantar pressure³⁸⁾; therefore, the cushioning effect of shoe 2 might have been even more pronounced when controlling for the step length. Plantar pressure distributions in shoe 3 were more equally distributed to the three foot regions (rear, middle, and forefoot), with the exception of zone 8 (toes), where maximum pressure values were significantly higher in shoe 3 (rocker-bottom shoe) than in the other shoes. These results are explained by the findings of Stewart et al.³⁹⁾ that the sloping design of the shoe base displaces the weight away from the heel. The lower pressure values under the midfoot and heel were a result of the shift in weight towards the front end of the foot. Accordingly, the CoP in posterior-anterior direction was clearly shorter when walking in shoe 3 (rocker-bottom shoe), and the first heel contact was closer to midfoot. This suggests that the rear foot is only briefly in contact with the surface^26,39). Shoe 3 also showed the shortest distance with regard to the medial-lateral CoP. As patients with knee osteoarthritis were found to have more lateral loading when compared with the CoP patterns of healthy subjects⁴⁰⁾, it would be expected that longer medial-lateral CoPs might not be beneficial for employees suffering from knee problems. In this context, Nigg et al.⁴¹⁾ reported pain reduction in patients with moderate knee osteoarthritis when wearing MTB shoes, which showed the shortest medial-lateral CoP in this study. The effects of an increase in medial-lateral direction are unclear from a preventive point of view though.

A limitation of the present study is the small pool of participants, whose results have to be interpreted carefully and do not yet allow for generalization. Another issue which needs to be discussed is the weight of the measuring system, as it might influence gait and plantar pressures. The CUELA system weighs three kilograms, which is a small weight compared to the body weight of the participants (approx. 3%-5% of the body weight). Furthermore, the weight of the system is distributed around extremities, with the main weight gathered around the waist (data logger). Therefore, the center of mass of the system is close to the center of mass of the body and therefore is not prone to influence body movements and particularly gait, as well as the distribution of plantar pressures, though the maximum plantar pressure might be slightly higher than in experiments with optical measurement systems. Future comparisons might be beneficial to prove this opinion.

All our measurements were carried out at the workplace, where the gold standard of gait analysis (three-dimensional infrared measuring systems) was not available, and we had to fall back to the mobile, robust CUELA system. The calibration of the insoles was conducted according to the manufacturer's instructions and the initialization of the CUELA system was carried out in a neutral body posture with no further means to control for the different shoes (e.g., stabilometers). Although this approach was similar to that of other authors⁴²⁾, some doubt remains about the absoluteness of this initial "calibration," particularly with regard to the rocker-bottom shoe. Nevertheless, we assume that our initialization is sufficient for the comparisons conducted in this study, as our results are in accordance with the results of other researchers⁴²⁾ and in accordance with a recent systematic review⁴³⁾.

Yet another aspect should be discussed, namely that this study about safety shoes bases on a "standardized" movement, i.e., walking on a plane surface at a given speed. Safety shoes should be examined at the workplace, where differences between the shoes might be more noticeable compared to measurements in standardized situations. Here lies the advantage of "field systems," e.g., the CUELA systems, which can be used in standardized situations as well as in laboratory settings. Note though that future examinations at the workplace should be adjusted for age, weight, foot size, and step length.

1) Johnson J.Footwear alleviates aches, fatigue through better fit, shock absorption. Occup Health Saf 1994; 63: 68-69. [PubMed] [Google Scholar]

2) Baur H, Bültermann D, Deibert P, et al.. Plantare Druckverteilung und muskuläre Aktivierung beim Tragen von Arbeitssicherheitsschuhen. Arbeitsmed Sozialmed Umweltmed 2003; 38: 12-16. [Google Scholar]

3) Brenton-Rule A, Bassett S, Walsh A, Rome K. The evaluation of walking footwear on postural stability in healthy older adults: an exploratory study. Clin Biomech 2011; 26: 885-887. [PubMed] [Google Scholar]

4) Kakihana W, Akai M, Yamasaki N, Takashima T, Nakazawa K. Changes of joint moments in teh gait of normal subjects wearing laterally wedged insoles. Am J Phys Med Rehabil 2004; 83: 273-278. [PubMed] [Google Scholar]

5) Wrobel JS, Edgar S, Cozzetto D, Maskill J, Peterson P, Najafi B. A proof-of-concept study for measuring gait speed, steadiness, and dynamic balance under various footwear conditions outside of the gait laboratory. J Am Podiatr med Assoc 2010; 100: 242-250. [PubMed] [Google Scholar]

6) Armstrong DG, Peters EJG, Athanasiou KA, Lavery LA. Is there a critical level of plantar foot pressure to identify patients at risk for neuropathic foot ulceration? J Foot Ankle Surg 1998; 37: 303-307. [PubMed] [Google Scholar]

7) Akbar-Khanzadeh F.Factors contributing to discomfort or dissatisfaction as a result of wearing personal protective equipment. J Hum Ergol 1998; 27: 70-75. [PubMed] [Google Scholar]

8) Marr SJ, Quine S. Shoe concerns and foot problems of wearers of safety footwear. Occup Med 1993; 43: 73-77. [PubMed] [Google Scholar]

9) Noll U, Krahn G, Leuchte S, Kraus T. Untersuchungen zum Boden-Schuh-System an typischen Arbeitsplätzen in der Automobilindustrie. Arbeitsmed Sozialmed Umweltmed 2008; 43: 320-324. [Google Scholar]

10) Ochsmann E, Kunst T, Gube M, Müller-Lux A, Kraus T. Kann durch individuelle Anpassung von Sicherheitsschuhen die Akzeptanz verbessert werden? In: Kraus T, Gube M, Kohl R, editors. Verhandlungen der Deutschen Gesellschaft für Arbeitsmedizin und Umweltmedizin. Aachen: 2009. p. 511-512. [Google Scholar]

11) Ellegast RP, Hermanns I, Schiefer C. Workload assessment in field using the ambulatory CUELA system. In: Duffy VG.Digital Human Modeling LNCS 5620. Berlin: Springer, 2009. p. 221-226. [Google Scholar]

12) Ellegast RP, Kupfer J. Portable posture and motion measuring system for use in ergonomic field analysis. In: Landau K.Ergonomic Software Tools in Product and Workplace Design. Stuttgart: 2000. p. 47-54. [Google Scholar]

13) Freitag S, Ellegast R, Dulon M, Nienhaus A. Quantitative measurement of stressful postures in nursing professions. Ann Occup Hyg 2007; 51(4): 385-395. [PubMed] [Google Scholar]

14) Glitsch U, Ottersbach HJ, Ellegast RP, Schaub K, Franz G, Jäger M. Physical workload of flight attendants when pushing and pulling trolleys aboard aircraft. Int J Ind Ergon 2007; 37: 845-854. [Google Scholar]

15) Ellegast RP, Kraft K, Groenesteijn L, Krause F, Berger H, Vink P. Comparison of four specific dynamic office chairs with a conventional office chair: impact upon muscle activation, physical activity and posture. Appl Ergonomics 2012; 43: 296-307. [PubMed] [Google Scholar]

16) Perry J, Burnfield JM. Gait Analysis: Normal and Pathological Function. second edThorofare: Slack; 2010. [Google Scholar]

17) World Medical Association. Declaration of Helsinki: Ethical principles for medical research involving human subjects. JAMA 2000; 284: 3043-3045. [PubMed] [Google Scholar]

18) Winter DA.The Biomechanics and Motor Control of Human Gait: Normal, Elderly and Pathological. Ontario: University of Waterloo Press; 1991. p. 121-143. [Google Scholar]

19) Li JX, Hong Y. Kinematic and electromyographic analysis of the trunk and lower limbs during walking in negative-heeled shoes. J Am Podiatr Med Assoc 2007; 97: 447-456. [PubMed] [Google Scholar]

20) New P, Pearce J. The effects of Masai Barefoot Technology footwear on posture: an experimental designed study. Physiother Res Int 2007; 12: 202. [Google Scholar]

21) Faber GS, Kingma I, Bruijn SM, van Dieen JH. Optimal inertial sensor location for ambulatory measurement of trunk inclination. J Biomechanics 2009; 42: 2406-2409. [PubMed] [Google Scholar]

22) Taloni S, Cassavia GC, Ciavarro GL, Andreoni G, Santambrogio GC, Pedotti A. An index for back pain risk assessment in nursery activities. Occup Ergonom 2004; 4: 281-290. [Google Scholar]

23) Hong Y, Cheung CK. Gait and posture responses to backpack load during level walking in children. Gait and Posture 2003; 17: 28-33. [PubMed] [Google Scholar]

24) Hoogendoorn WE, Bongers PM, de Vet HC, et al.. Flexion and rotation of the trunk and lifting at work are risk factors for low back pain: results of a prospective cohort study. Spine 2000; 25: 3087-3092. [PubMed] [Google Scholar]

25) Romkes J, Rudmann C, Brunner R. Changes in gait and EMG when walking with the Masai Barefoot Technique. Clin Biomech 2006; 21: 75-81. [PubMed] [Google Scholar]

26) Nigg B, Hintzen S, Ferber R. Effect of an unstable shoe construction on lower extremity gait characteristics. Clin Biomech 2006; 21: 82-88. [PubMed] [Google Scholar]

27) Troup JDG, Hood CA, Chapman AE. Measurements of the sagittal mobility of the lumbar spine and hips. Ann Phys Med 1968; 9: 308-321. [PubMed] [Google Scholar]

28) Wegener C, Hunt AE, VanWanseele B, Burns J, Smith RM. Effects of children's shoes on gait: a systematic review and meta analysis. J Foot Ankle Res 2011; 4: 1-13. [PMC free article] [PubMed] [Google Scholar]

29) Valmassy R.Clinical biomechanics of the lower extremities. St Louis: Mosby; 1996. [Google Scholar]

30) Lee CE, Simmonds MJ, Etnyre BR, Morris GS. Influence of pain distribution on gait characteristics in patients with low back pain. Part 1: vertical ground reaction force. Spine 2007; 32: 1329-1336. [PubMed] [Google Scholar]

31) Nigg BM, Denoth J. Sportplatzbelaege. Zurich: Juris Verlag; 1980. [Google Scholar]

32) Elbaz A, Mirovsky Y, Mor A, et al.. A novel biomechanical device improves gait pattern in patient with chronic nonspecific low back pain. Spine 2009; 34: E507-512. [PubMed] [Google Scholar]

33) Taylor NF, Evans OM, Goldie PA. The effect of walking faster on people whith acute low back pain. Eur Spine J 2003; 12: 166-172. [PMC free article] [PubMed] [Google Scholar]

34) Huang Y, Meijer OG, Lin J, et al.. The effects of stride length and stride frequency on trunk coordination in human walking. Gait Posture 2010; 31: 444-449. [PubMed] [Google Scholar]

35) Schulze C, Lindner T, Woitke S, et al.. Influence of footwear and equipment on stride length and range of motion of ankle, knee and hip joint. Acta Bioeng Biomech 2014; 16: 45-51. [PubMed] [Google Scholar]

36) Walther M, Grosse V. Vorfußdämpfung im Sicherheitsschuh-eine prospektive Studie in der Automobilindustrie. Zentralbl Arbeitsmed 2006; 56: 312-321. [Google Scholar]

37) Werner RA, Gell N, Hartigan A, Wiggermann N, Keyserling WM. Risk factors for foot and ankle disorders among assembly plant workers. Am J Ind Med 2010; 53: 1233-1239. [PubMed] [Google Scholar]

38) Allet L, IJzerman H, Meijer K, Willems P, Savelberg H. The influence of stride-length on plantar foot-pressures and joint moments. Gait Posture 2011; 34: 300-306. [PubMed] [Google Scholar]

39) Stewart L, Gibson JNA, Thomson CE. In-shoe pressure distribution in "unstable" (MBT) shoes and flat-bottomed training shoes: A comparative study. Gait & Posture 2007; 25: 648-651. [PubMed] [Google Scholar]

40) Lidtke RH, Muehleman C, Kwasny M, Block JA. Foot center of pressure and medial knee osteoarthritis. J Am Podiatr Med Assoc 2010; 100: 178-184. [PubMed] [Google Scholar]

41) Nigg BM, Emery C, Hiemstra LA. Unstable shoe construction and reduction of pain in osteoarthritis patients. Med Sci Sports Exerc 2006; 38: 1701-1708. [PubMed] [Google Scholar]

42) Stewart L, Gibson JLA, Thomson CE. In shoe pressure distribution in "unstable" (MBT) shoes and flat-bottomed training shoes: a comparative study. Gait Posture 2007; 25: 648-651. [PubMed] [Google Scholar]

43) Tan JM, Auhl M, Menz HB, Levinger B, Munteau SE. The effect of Masai Barefoot Technology (MBT) footwear on lower limb biomechanics: a systematic review. Gait Posture 2016; 43: 76-86. [PubMed] [Google Scholar]